Back to Blog
How-to Guides 2026-11-20 Addicted To Audio - Home Audio Electronics & Accessories 0 views

How to Install a Phono Preamplifier for Your Turntable Setup

How to Install a Phono Preamplifier for Your Turntable Setup

A practical guide to connecting a phono preamp, with setup tips and a close look at the Violectric PPA V790's adjustable cartridge settings.

Why Install a Dedicated Phono Preamplifier?

A turntable's cartridge outputs a very low-level signal that needs both amplification and equalization before your amplifier can handle it. Many integrated amplifiers and receivers include a built-in phono stage, but a separate phono preamplifier offers greater control over gain, impedance, and equalization curves—especially if you use multiple cartridges or vintage records.

Installing a phono preamp is straightforward: you connect the turntable's RCA cables to the preamp's input, then run the preamp's output to an unused line-level input on your amplifier or receiver. The real work comes in configuring the preamp to match your cartridge's electrical characteristics.

Step-by-Step Connection Process

These steps assume you have a turntable with a standard RCA output and a separate phono preamplifier. Always power off all components before making connections.

  1. Position the preamp: Place the phono preamp near your turntable and amplifier so the RCA cables reach without strain. Keep it away from power transformers or other sources of electromagnetic interference.
  2. Connect the turntable to the preamp input: Plug the turntable's RCA cables into the preamp's input jacks. If your turntable has a ground wire, connect it to the preamp's ground terminal—this helps reduce hum.
  3. Connect the preamp output to your amplifier: Use a second pair of RCA cables to connect the preamp's output to any line-level input on your amplifier (aux, CD, tuner, etc.). Do not use the amplifier's phono input—that would apply a second stage of equalization.
  4. Power on and set gain: Turn on the preamp first, then your amplifier. Start with the gain set low (around +30 dB) and increase gradually while playing a record until the volume matches your other sources without distortion.

Matching the Preamp to Your Cartridge

A phono preamplifier must be configured to match your cartridge's output type and electrical load. The usual split is MM (moving magnet) and MC (moving coil), but some preamps—like the Violectric PPA V790—allow you to treat each cartridge individually regardless of type.

The PPA V790 offers a wide gain adjustment from +30 dB to +66 dB, covering everything from high-output MC cartridges to low-output moving coils. You can also set input impedance, input capacitance, EQ curve, subsonic filter, and output boost separately for each of the six connected cartridges. All settings are stored and displayed via front-panel push buttons and white LEDs.

Violectric PPA V790 – Key Adjustable Parameters

  • Violectric PPA V790 Phono Preamplifier: Gain adjustable in 7 steps from +30 dB to +66 dB. This wide range lets you use both low-output MC and high-output MM cartridges without needing an additional step-up transformer.
    Violectric PPA V790 Phono Preamplifier
    Violectric PPA V790 Phono Preamplifier
  • Violectric PPA V790 Phono Preamplifier: Supports up to six cartridges (3 balanced, 3 unbalanced) with individually stored settings for impedance, capacity, EQ, subsonic filter, and boost. If you own multiple turntables or swap cartridges frequently, you can store each configuration and recall it instantly without re-adjusting every parameter.
  • Violectric PPA V790 Phono Preamplifier: Offers three DC-coupled EQ curves: RIAA, NAB, and Columbia-LP. Vintage or non-standard records may require a different equalization curve than the modern RIAA standard. Having NAB and Columbia-LP on board lets you play those recordings with correct frequency response.

Setting the EQ Curve and Subsonic Filter

Most modern records use the RIAA equalization curve, which is the default on virtually all phono preamps. However, some preamps—including the PPA V790—also include NAB and Columbia-LP curves for older or specialty pressings. If you play mostly recent vinyl, stick with RIAA.

A switchable subsonic filter removes low-frequency rumble that can cause woofer flutter or amplifier strain. Engage it if your turntable is on a bouncy floor or if you notice excessive cone movement on quiet passages. The filter is adjustable per input on the PPA V790.

Using the Boost Feature for System Integration

The PPA V790 includes a boost circuit with 0, +6, and +12 dB settings. This is not a tone control—it is intended to match the preamp's output level to your amplifier's input sensitivity. If your preamp's output seems too low compared to other sources, try the +6 dB setting first. The +12 dB setting is useful for very quiet cartridges or systems with low-gain preamplifier inputs.

What to Do If You Hear Hum or Noise

Hum is usually caused by a missing ground connection or a ground loop. Confirm that the turntable's ground wire is attached to the preamp's ground terminal. If the hum persists, try moving the preamp away from other electronics or using a different power outlet. A clip indication on the PPA V790 warns you if the input signal is too high, which can cause distortion—reduce the gain if the clip indicator lights.

Related Articles

Customer Service
Home
Products
Cart
Profile