The stand decision comes before the room plan
The Concept 300 is sold as a pair of standmount speakers, and Q Acoustics offers it in two forms: with the Tensegrity stand and isolation base system, or without stands. That choice shapes everything else about placement. The stand is not a generic accessory in this design—Q Acoustics describes the Tensegrity as a tripod structure built from precision machined stainless steel rods and thin stainless steel cables, and the speaker connects to it through an isolation base suspension system with four springs. If you choose the No Stands version, you will need to supply your own support, and the supplied information does not specify a third-party stand requirement or a recommended height. Treat that as an open decision rather than a solved one.
What the Concept 300 package confirms
- Q Acoustics Concept 300 Bookshelf Speakers (Pair): Sold as a pair of speakers, with variants for Silver and Ebony, Black and Rosewood, and White and Light Oak, each available with or without stands. The stand choice is part of the product variant, not an afterthought, so decide it before you plan the room.

Q Acoustics Concept 300 Bookshelf Speakers (Pair) - Q Acoustics Concept 300 Bookshelf Speakers (Pair): The Tensegrity stand and isolation base system suspend the entire mass of the Concept 300 on four springs in an integrated base plate. This is the support method Q Acoustics designed for the speaker, and it affects how the speaker sits in the room.
- Q Acoustics Concept 300 Bookshelf Speakers (Pair): The cabinet uses P2P (point to point) bracing and Dual Gelcore construction, with three layers separated by a non-setting gel. These are cabinet-vibration controls, not room-correction features, so placement still matters for the sound you hear.
Room setup: what the catalog does and does not tell you
Q Acoustics does not supply a recommended distance from the wall, a toe-in angle or a listening distance for the Concept 300 in the available information. That is a real limitation for a buying guide, because a standmount speaker's bass and midrange balance changes with boundary proximity. The honest approach is to plan for adjustment rather than treat a single position as correct. Start with the speakers clear of the wall behind them, listen, and move them incrementally. The catalog does confirm the drivers: a 165mm impregnated/coated paper cone mid/bass driver with a rubber surround, and a 28mm high-frequency driver made of coated microfibre strands, decoupled from the cabinet with a rubber gasket. Those drivers are the reason placement changes what you hear, but they do not replace a listening test in your room.
A practical placement sequence for the Concept 300
- Decide on the stand first: If you choose the Including Stands version, the Tensegrity stand and isolation base define the footprint and the speaker's supported position. If you choose No Stands, confirm your own stand's stability and height before positioning, because the supplied information does not specify a third-party stand standard.
- Leave room to move the speakers: Because no wall distance is supplied, plan a position that lets you shift the speakers forward and back. A standmount with a 165mm mid/bass driver will interact with the wall behind it, so adjust in small steps and listen for changes in bass weight and midrange clarity.
- Plan the cable run around the terminals: The rear terminal panel is over-specified to resist cabinet vibrations and is equipped for bi-wiring or bi-amping via electrically isolated terminals. It accepts bare wire, spade connectors or 4mm banana plugs. Decide whether you will bi-wire before you finalize the position, because extra cable runs need space behind the speaker.
- Check the finish against the room: The cabinet combines real-wood veneers with a high-gloss lacquer finish. The three colour pairs—Silver and Ebony, Black and Rosewood, and White and Light Oak—are a visual decision as much as an acoustic one, so consider the room's light and furnishings before ordering.
Bi-wiring and bi-amping: a connection choice, not a placement fix
The Concept 300's terminals support bi-wiring or bi-amping, and they accept bare wire, spade connectors or 4mm banana plugs. That flexibility is useful, but it does not correct a room problem. If you bi-amp, you will need two amplifier channels per speaker and the space behind each speaker for the additional cable. The supplied information does not state a minimum amplifier power or a recommended cable gauge, so those remain decisions to confirm with your dealer rather than assumptions to make from the catalog.
Driver and terminal details that shape the setup
- Q Acoustics Concept 300 Bookshelf Speakers (Pair): The mid/bass driver is a 165mm impregnated/coated paper cone with a high-performance rubber surround, sitting in front of a 35mm glass fibre voice coil and a ferrite magnet. This is the driver most affected by wall proximity, so give yourself room to adjust the speaker's distance from the front wall.
- Q Acoustics Concept 300 Bookshelf Speakers (Pair): The 28mm high-frequency driver is made of super-fine strands of coated microfibre and is decoupled from the cabinet using a rubber gasket. The decoupling is a cabinet-level control; it does not remove the need to aim the speaker toward the listening position.
- Q Acoustics Concept 300 Bookshelf Speakers (Pair): The rear terminal panel is equipped for bi-wiring or bi-amping via electrically isolated terminals that accept bare wire, spade connectors or 4mm banana plugs. Confirm your cable termination and bi-wire plan before you lock in the speaker position.
The honest trade-offs before you buy
The Concept 300 is a high-end standmount with a cabinet and stand design that Q Acoustics has engineered to minimize vibration. That engineering is the product's appeal, but it also means the stand is part of the system rather than an optional extra. If you choose No Stands, you are taking on a support decision the catalog does not resolve. If you choose Including Stands, you are committing to the Tensegrity footprint and the four-spring isolation base. Neither choice comes with a supplied wall-distance recommendation, so your room and your willingness to experiment will determine the final sound. The catalog price is USD 4555.32, with a comparison price of USD 6699.00, but the more important budget question is whether your room allows the placement adjustments this speaker deserves.

