The problem the HE-Adapter solves
Low-efficiency planar headphones such as the HiFiMAN HE-6 need a lot of power, and many headphone amplifiers struggle to deliver it. A speaker amplifier has power to spare, but its speaker outputs are not designed to connect straight to a headphone cable. The HiFiMAN HE-Adapter sits between the two: speaker cables go in, and a 4-pin XLR headphone output comes out.
That is the whole idea. You are not adding a second amplifier or changing the way your system sounds at the source; you are giving the headphones a safe, matched path to the amplifier you already own.
What the HE-Adapter actually is
- HiFiMAN HE-Adapter: The HE-Adapter has a speaker connector input and a 4-pin XLR output. These are the two interfaces that determine whether it fits your system: your amplifier needs speaker outputs, and your headphones need a 4-pin XLR cable.

HiFiMAN HE-Adapter - HiFiMAN HE-Adapter: It measures 16.5 cm x 12.2 cm x 7.5 cm (6.5 inches x 4.8 inches x 2.9 inches) and weighs 542 g. It is a compact box rather than a full-size component, so plan a spot near your amplifier where the speaker cables and headphone cable can reach without strain.
How to set it up
The supplied information confirms the interfaces but does not include a step-by-step manufacturer procedure. The sequence below follows directly from those interfaces; check your amplifier's own instructions for anything specific to it.
- Confirm the headphone is supported: The HE-Adapter is designed for the HiFiMAN HE-6, HE-5LE and HE-4. It is not compatible with high-efficiency headphones such as the HE-500, so check your model before connecting anything.
- Power down before you connect: Switch off the amplifier before making connections. The supplied information does not describe a live-connection procedure, so treat powering down as the safe default.
- Connect the amplifier's speaker outputs to the adapter's speaker input: Use speaker cables from your integrated or power amplifier's speaker outputs to the HE-Adapter's speaker connector input. This is the path that lets the headphones draw on the amplifier's high power output.
- Plug the headphones into the 4-pin XLR output: The adapter's output is a 4-pin XLR connection. Your headphone cable needs to match that connector; the supplied information does not describe separate adapters for other plug types.
- Start at a low volume: Bring the volume up gradually from the amplifier's control. The supplied information gives no specific volume settings, so use your ears and your amplifier's normal practice.
What the resistors inside are doing
Inside the HE-Adapter are resistors in parallel and in series, which the catalog describes as helping to optimize the signal and provide better impedance matching between the amplifier and headphones. In plain terms, the adapter is not a bare pass-through: it presents the amplifier with a load closer to what it expects from a speaker, while feeding the headphones a signal suited to their low efficiency.
The catalog does not publish a recommended amplifier power range or a minimum or maximum output figure for the adapter. If your amplifier's manual specifies limits for speaker loads, compare those with the adapter's stated resistor arrangement rather than assuming any speaker amp is suitable.
HE-Adapter vs a dedicated headphone amplifier
Both routes can drive demanding planar headphones, but they suit different systems.
- HE-Adapter with your speaker amplifier: Best if you already own a good integrated or power amplifier and want to use its power output with HE-6, HE-5LE or HE-4 headphones. It adds one box and a pair of speaker cable runs, and it only works with the supported low-efficiency models.
- A dedicated headphone amplifier: Best if you want a single box with headphone outputs built for headphones, without speaker cables. The trade-off is that you are buying amplification you may already have in your speaker system.
Checks before you buy
- Headphone model: HE-6, HE-5LE or HE-4 only. High-efficiency models such as the HE-500 are explicitly not compatible.
- Headphone cable termination: The adapter output is 4-pin XLR. Confirm your cable ends in that connector.
- Amplifier outputs: You need speaker outputs on an integrated or power amplifier. The supplied information does not describe line-level or preamp-only connections.
- Space and cable reach: At 16.5 cm x 12.2 cm x 7.5 cm and 542 g, the adapter needs a stable spot within reach of both the speaker cables and your listening position.
What the supplied information does not cover
The catalog does not include a manufacturer setup procedure, a supported amplifier power range, or guidance on cable length and gauge. It also does not confirm compatibility with headphone models beyond the HE-6, HE-5LE and HE-4, or with headphone cables that use terminations other than 4-pin XLR. Where those details matter to your system, verify them with the manufacturer or your dealer before connecting. The HE-Adapter is a focused tool: used with the right headphones and a speaker amplifier, it turns power you already own into a usable headphone signal.

